An animation showing the Tog-L-Loc process

BTM Fully Adaptable Hand Held Clinching Units

Can be adapted to your requirements to make the perfect combination for maximum productivity.

Limitless Configuration Possibilities

The Fully Adaptable Unit is all about flexibility due to its customizable features. Joint size, accessibility to the part, throat depth, opening, force requirement, and ergonomics can all be designed to your requirements to make the perfect combination for maximum productivity.


Example of a Fully Adaptable Clinch Unit

Example of a Fully Adaptable Clinch Unit

Basic Product Specifications

  • Power Source: May Require a Custom Hydraulic Pump
  • Max. Combined Material Thickness: 4mm [.16in]
  • Clinch Tooling Compatibility: Round or Geo-Clinch® Joints
  • Tooling Sizes: 3.0, 3.8, 4.6, 5.5, 6.4

A Fully Adaptable Unit may be Ideal if:

  • You need a high degree of flexibility and force.
  • Your part has difficult to reach joint locations.
  • Your force requirements exceed a standard unit.

General Information

The following sections contain general information about the product.

These units are customizable. Click on the product below to view a catalog page with more detailed information:


Product Description
Fully Adaptable Unit

Fully Adaptable Unit

 		If your part requires a larger stroke, requires a deeper throat depth and/or your material is thick, this is the unit to consider. A wide range of cylinder bore sizes and strokes along with existing "C" frames are available, or can be modified to fit your part.

Our standard hydraulic power unit can be supplied unless design parameters require a custom power unit.

BTM offers the HydroPak2, depending on the configuration of the unit. For more detailed information click on the product below to view a catalog page.


Product Electrical Supply Power Consumption Max Pressure Max. Working Pressure Tank Capacity Weight (without oil)
HydroPak2 Hydraulic Pump

HydroPak2

 		480 VAC 60 HZ single phase 20 amp 3800 watts 207 BAR [3000 PSI] 45/172 BAR [650/2500 PSI] 94.6 Liters [25 Gallons] 224 kg [492 lb]

Application Information

The following sections are provided to help match a Hand Held Unit to your part. More detailed information is typically available in our Product Literature section.
If you are considering this product for your project, please view the contact information below.

Jump to a Section:

Shown here are some typical applications that a Fully Adaptable unit may be compatible with.
Not sure if your part is compatible with a bayonet unit? Contact a BTM Application Engineer for assistance.


  • Overlap1.) Overlap
  • Angle and Sheet2.) Angle and Sheet
  • Angle and Sheet Sandwich3.) Angle and Sheet Sandwich
  • "T" and Sheet4.) "T" and Sheet
  • Outside Edge Flange6.) Outside Edge Flange
  • Hat on Sheet8.) Hat on Sheet
  • Inside Edge Flange11.) Inside Edge Flange
  • "U" and Sheet12.) "U" and Sheet
  • Bottom To Bottom "U's"13.) Bottom To Bottom "U's"
  • Two Piece Full Corner Overlap17.) Two Piece Full Corner Overlap
  • Full Corner Joggle Overlap18.) Full Corner Joggle Overlap
  • 45° Corner Overlap19.) 45° Corner Overlap
  • Corner Joggle Overlap w/ Ret. Flange20.) Corner Joggle Overlap w/ Ret. Flange
  • Hat Inside "U"21.) Hat Inside "U"

Download the Product Catalog to find technical information about the product.

Would you like to know if a Fully Adaptable Clinch Unit is a good fit for your application, or would you like a quote?
Talk to an Application Engineer at 810-364-4567, or email us at sales@btmcorp.com. Business hours are 8am-4:30pm ET Mon-Fri.
You may also contact us by filling out the form below.


To help us with the quoting process, please email a drawing or CAD model of your part.
(If your drawing is near 10mb or larger, our FTP site is available. Contact BTM to obtain login information.)


If you would like clarification on the terms used in the form, Click Here to View a Catalog Page

Fully Adaptable Hand Held Units Contact Form

Unit Requirements:

Application Info:

i The Punch Side has the "cavity" side of the joint. Punch Side and Button Side Example Note: Thicker material usually goes on the punch side.
i The Die Side has the "button" side of the joint. Punch Side and Button Side Example Note: Thicker material usually goes on the punch side.
* - Denotes a Required Field.

You may also be interested in the following BTM Hand Held Clinching Units:

Customer Information

The following section contains information for customers who have already purchased this product.

If you have already purchased this product, please fill out a brief customer satisfaction survey and let us know what you think.


Service Information

Customer Satisfaction Survey